Universal Guide How To Enable zRAM / Swap in Any Custom Rom – MT65XX

What Is zRAM/Swap?
How to Enable zRAM / Swap in Any Custom Rom – MT65XX. zRAM is a Linux kernel function that gives a form of virtual memory compressionzRAM increases overall performance by way of keeping off paging to disk and the usage of a compressed block device in RAM instead, inside which paging takes area until it is essential to apply the swap area on a hard disk drive. since using zRAM is an alternative way to provide swapping on RAM, zRAM allows Linux to make a better use of RAM when swapping/paging is needed, specifically on older Devices with much less RAM installed.
Requirements :- 
  • PC
  • Text Editor :-  CLICK HERE ^(http://ouo.io/4Ir5lR)
  • tiny*** files :- CLICK HERE ^(http://ouo.io/txVG8tC)
  • Knowledge about unpacking and repacking boot.img
  • Read : 
  • Unpack, Edit, Port, Repack Boot.img/kernel/Recovery.img Without PC ^(http://ouo.io/aBvriY)
  • How To Port boot.img And Port Kernel- Unpack/Repack – PC ^(http://ouo.io/dphdar)
Procedure :- 
1. Download these 4 tiny*** files :- CLICK HERE ^(http://ouo.io/txVG8tC)and Extract it you will get following 4 files listed below-
tiny_mkswap
tiny_swapoff
tiny_swapon
tiny_switch
2. Now Copy these files and paste in a Folder.
3. Extract the Rom(in which do you want to enable swap or zram)
4. Now go to System – Bin folder and paste those four files here (all tiny** files)
5. Unpack the boot.img and go to initrd or Ramdisk folder :-
6. See if there is any enableswap.sh file?
7. If yes, then NO need to do or edit anything in boot.im
8. If no, Download this zip file :- CLICK HERE ^(http://ouo.io/cc9Gqg)
9. You will see these two following files listed Below :
  • enableswap.sh
  • init.rc file
10. Now copy enableswap.sh and paste in ramdisk folder.

Now open init.rc file you’ve downloaded in step 9 and copy all Lines –

1. If your rom is Kitkat/Kitkat based (4.4.x) :- 
  • Open init.rc (in ramdisk) with Notepad++ and paste in bottom. and Save it.
  • Repack the boot.img and replace it with your existing boot.img.
  • Zip the Rom And Flash it

2. If your Rom is Lollipop/Lollipop Based (5.x.x) :-
  • Open init.mt65xx.rc (in ramdisk) with Notepad++ and paste in bottom and Save it.
  • Repack the boot.img and replace it with your existing boot.img..zip the Rom And Flash it

3. your rom is Marshmallow or Nougat (6.x.x or 7.x.x) :- 
  • Open init.mt65xx_common.rc (in ramdisk or initrd folder) with Notepad++ and paste in bottom and Save it( if init.mt65xx_common.rc is not available, Paste it in init.mt65xx.rc)
  • Repack the boot.img and replace it with your existing boot.img..zip the Rom And Flash it


Note:- Using This Guide You can enable only 512MB zRam

If you have any queries about this guide, comment below.

Screenshot :- 

MT65xx Preloader Usb Driver MTK6577 USB VCOM Driver Download And Installation

MT65xx Preloader Usb Driving force MTK6577 USB VCOM Driving force Obtain And Set up USB VCOM driving force set up for MTK6577 seem Telephones, here’s a brief information to the set up, and a last, a success check with SPFlashtool! Set up of the USB VCOM driving force:

Obtain Mtk Mt65xx Preloader Usb Driving force MTK6577 All

Driving force IdentifyHome windowsObtain Hyperlinks
MT65xx Preloader.zipALLObtain
MT65xx MT6577 USB VCOMWin7, Winxp, WinVista, Win10Obtain ^(http://www.mediafire.com/download/v56i463v5j6whqg/MT6577_USB_VCOM_drivers_%28W7VistaXP%29_2.zip)
MT65xx MT6577 USB VCOMHome windows 8Obtain ^(http://www.mediafire.com/download/4caryyy5iiduoy8/SP_Drivers_v1.4++Windows+8.zip)
USB Deview32 bit x86Obtain ^(http://www.mediafire.com/download/iqa3f1m7vuei313/usbdeview+32+bit.zip)
USB Deview64 bit x64Obtain ^(http://www.mediafire.com/download/bq88jjbp9qgrqkk/USBDeview+x64+bit.zip)

[1] With USBDeview, blank up your PC from all conceivable outdated MTK VCOM entries, then reboot your PC [2] Smartphone is switched off, and nonetheless dont attach by way of USB to the PC. [3] Open Tool Supervisor and go away it open! [4] Your switched off Smartphone with inserted rechargeable battery by way of USB attach now at the PC, you must now see a MT65xx preloader within the Tool Supervisor. (With some MTK6577 Smartphones must be put in with out battery. Please earlier than hand tell.) [5] now release the Installdriver.exe from the unzipped MT6577 USB VCOM drivers folder. Verify the set up of u [6] now! (W7 x 64 this affirmation comes later within the handbook set up!) After the set up is entire, you haven’t any access within the Tool Supervisor, it’s appropriately [7] PC reboot! [8] Open Tool Supervisor and open the switched-off Smartphone by way of USB to the PC free up, now attach (similar USB port!) [9] Now a MediaTek PreLoader USB VCOM must seem for a temporary second within the Tool Supervisor access! [10] These days the access double click on and click on on “Replace driving force” beneath the tab “Driving force”. [11] With the wizard within the unzipped MTK 6577 USB VCOM drivers navigate and make a selection the folder to your working gadget. All Mtk And Mediatek Usb Driving force mtk usb driving force home windows 7 64 bit mtk usb driving force home windows 7 x64 mtk usb driving force home windows 7 32 bit obtain mtk usb driving force for home windows 7 mtk usb driving force for home windows 7 32bit mtk usb driving force for home windows 7 loose obtain mtk usb driving force for home windows xp loose obtain all mtk usb driving force